SA Alloy C-276 | Certilas: The filler metal specialist

Go Back

productspecificaties
Verpakkingen
vraag offerte

Type

Solid wire for nickel-chromium-molybdenum alloys

classification

AWS

A 5.14: ERNiCrMo-4

EN ISO

18274: S Ni 6276 (NiCr15Mo16Fe6W4)

W.Nr.

2.4886

Toepassingen

CEWELD SA Alloy C-276 is used for welding low carbon nickel-chromium-molybdenum alloys, especially UNS N10276, for welding the clad side in steel clad with low carbon nickel-chromium-molybdenum alloy, and for welding low carbon nickel-chromium-molybdenum alloys to steel and other nickel-base alloys.

Type

Solid wire for nickel-chromium-molybdenum alloys

Toepassingen

CEWELD SA Alloy C-276 is used for welding low carbon nickel-chromium-molybdenum alloys, especially UNS N10276, for welding the clad side in steel clad with low carbon nickel-chromium-molybdenum alloy, and for welding low carbon nickel-chromium-molybdenum alloys to steel and other nickel-base alloys.

Eigenschappen

High Nickel-Chromium alloy with very good mechanical properties down to -196°C. This wire can be welded with our fused flux FL 880 or agglomerated flux FL 838 or FL 839.

Classificatie

AWS

A 5.14: ERNiCrMo-4

EN ISO

18274: S Ni 6276 (NiCr15Mo16Fe6W4)

F-nr

45

FM

6

W.Nr.

2.4886

Geschikt voor

Alloy 276, Ni 6276 (NiCr15Mo16Fe6W4). 2.4886, 2.4887

M.No: 1.5680, 1.5682, 2.4819, 2.4883

NiMo16Cr15W, X12Ni5 / 12Ni19, X8Ni9, G-NiMo16Cr

Alloy C4, Hastelloy C276, A494CW-12MW, A743 / A744CW-12M

Lasposities

Herdrogen

Not required

Analyse

C	Si	Mn	Cr	Ni	Mo	Nb	Ti	V	Fe	W	Co	Cu	Al	P	S	Nb+Ta
0.01	0.07	0.9	15.5	62	16			0.2	6	4	2

Mechanische waarden

Heat Treatment	R_P0,2 (MPa)	Rm (MPa)	A5 (%)	Impact Energy (J) ISO-V	Hardness
Heat Treatment	R_P0,2 (MPa)	Rm (MPa)	A5 (%)	RT	Hardness
As Welded	410	710	35	80	HRc

productblad

prestatieverklaring

conformiteitsverklaring

VIB

productblad

VIB

submerged arc welding wire for inconel 600 - alloy c SA c 276

Disclaimer

Whilst all reasonable efforts have been made to ensure the accuracy of the information contained, the information contained or otherwise referenced herein is presented only as “typical” without guarantee or warranty, and any liability incurred from any reliance thereon is expressively disclaimed. Typical data are those obtained when welded and tested in accordance to prescribed standards, and should not be assumed to be the expected results in a particular application or weldment. Other tests and procedures may produce different results. Users are cautioned to confirm by qualification testing, or other appropriate means, the suitability of any welding consumable and procedure before use in the intended application. The selection and use of specific products is solely within the control of, and remains the sole responsibility of the customer. The right to change design and/or specifications without notice is reserved.